Definition of RAID
Redundant Array of Independent Disks (RAID) is a virtual disk technology that combines multiple physical drives into one unit. RAID can create redundancy, improve performance, or do both.
RAID should not be considered a replacement for backing up your data. If critical data is going onto a RAID array, it should be backed up to another physical drive or logical set of drives.
The following are terms that are normally used in connection with RAID:
· Striping: data is split between multiple disks.
· Mirroring: data is mirrored between multiple disks.
· Parity: also referred to as a checksum. Parity is a calculated value used to mathematically rebuild data.
Different RAID levels exist for different application requirements.
Types of Raid:-
· RAID 0– striping Click Here
· RAID 1 – mirroring Click Here
· RAID 5 – striping with parity Click Here
· RAID 6 – striping with double parity Click Here
· RAID 10(1+0)– combining mirroring and striping Click Here
1. RAID 0
In a RAID 0 system data are split up into blocks that get written across all the drives in the array. By using multiple disks (at least 2) at the same time, this offers superior I/O performance. This performance can be enhanced further by using multiple controllers, ideally one controller per disk.
Img RAID 0
Advantages of RAID 0
· RAID 0 offers great performance, both in read and write operations. There is no overhead caused by parity controls.
· All storage capacity is used, there is no overhead.
· The technology is easy to implement.
Disadvantages of RAID 0
· RAID 0 is not fault-tolerant. If one drive fails, all data in the RAID 0 array are lost. It should not be used for mission-critical systems.
Ideal use
RAID 0 is ideal for non-critical storage of data that have to be read/written at a high speed,
2. RAID 1
Data are stored twice by writing them to both the data drive (or set of data drives) and a mirror drive (or set of drives). If a drive fails, the controller uses either the data drive or the mirror drive for data recovery and continuous operation. You need at least 2 drives for a RAID 1 array.
Img RAID 1
Advantages of RAID 1
· RAID 1 offers excellent read speed and a write-speed that is comparable to that of a single drive.
· In case a drive fails, data do not have to be rebuild, they just have to be copied to the replacement drive.
· RAID 1 is a very simple technology.
Disadvantages of RAID 1
· The main disadvantage is that the effective storage capacity is only half of the total drive capacity because all data get written twice.
· Software RAID 1 solutions do not always allow a hot swap of a failed drive. That means the failed drive can only be replaced after powering down the computer it is attached to. For servers that are used simultaneously by many people, this may not be acceptable. Such systems typically use hardware controllers that do support hot swapping.
Ideal use
RAID-1 is ideal for mission critical storage, for instance for accounting systems.
3. RAID 5
RAID 5 is the most common secure RAID level. It requires at least 3 drives but can work with up to 16. Data blocks are striped across the drives and on one drive a parity checksum of all the block data is written. The parity data are not written to a fixed drive, they are spread across all drives, as the drawing below shows. Using the parity data, the computer can recalculate the data of one of the other data blocks, should those data no longer be available. That means a RAID 5 array can withstand a single drive failure without losing data or access to data. Although RAID 5 can be achieved in software, a hardware controller is recommended. Often extra cache memory is used on these controllers to improve the write performance.
Img RAID 5
Advantages of RAID 5
· Read data transactions are very fast while write data transactions are somewhat slower (due to the parity that has to be calculated).
· If a drive fails, you still have access to all data, even while the failed drive is being replaced and the storage controller rebuilds the data on the new drive.
Disadvantages of RAID 5
· Drive failures have an effect on throughput, although this is still acceptable.
· This is complex technology. If one of the disks in an array using 4TB disks fails and is replaced, restoring the data (the rebuild time) may take a day or longer, depending on the load on the array and the speed of the controller. If another disk goes bad during that time, data are lost forever.
Ideal use
RAID 5 is a good all-round system that combines efficient storage with excellent security and decent performance.
4. RAID 6
RAID 6 is like RAID 5, but the parity data are written to two drives. That means it requires at least 4 drives and can withstand 2 drives dying simultaneously. The chances that two drives break down at exactly the same moment are of course very small. However, if a drive in a RAID 5 systems dies and is replaced by a new drive, it takes hours or even more than a day to rebuild the swapped drive. If another drive dies during that time, you still lose all of your data. With RAID 6, the RAID array will even survive that second failure.
Img RAID 6
Advantages of RAID 6
· Like with RAID 5, read data transactions are very fast.
· If two drives fail, you still have access to all data, even while the failed drives are being replaced. So RAID 6 is more secure than RAID 5.
Disadvantages of RAID 6
· Write data transactions are slower than RAID 5 due to the additional parity data that have to be calculated. In one report I read the write performance was 20% lower.
· Drive failures have an effect on throughput, although this is still acceptable.
· This is complex technology. Rebuilding an array in which one drive failed can take a long time.
Ideal use
RAID 6 is a good all-round system that combines efficient storage with excellent security and decent performance. It is preferable over RAID 5 in file and application servers that use many large drives for data storage.
5. RAID 10
It is possible to combine the advantages (and disadvantages) of RAID 0 and RAID 1 in one single system. This is a nested or hybrid RAID configuration. It provides security by mirroring all data on secondary drives while using striping across each set of drives to speed up data transfers.
Img RAID 10
Advantages of RAID 10
· If something goes wrong with one of the disks in a RAID 10 configuration, the rebuild time is very fast since all that is needed is copying all the data from the surviving mirror to a new drive. This can take as little as 30 minutes for drives of 1 TB.
Disadvantages of RAID 10
· Half of the storage capacity goes to mirroring, so compared to large RAID 5 or RAID 6 arrays, this is an expensive way to have redundancy.
Good Article 👍
ReplyDeleteGood
ReplyDelete